Long 28 Spline 9 Inch Fits Ford Cut-to-Fit Axle with Bearing

Description: Fits Ford 9 inch axle housings with New "Torino" big bearing flange, 3.150" O.D. bearing, 2-1/2" offset, Choice of 28, 31, or 35 splines to fit multiple applications and are cut to fit for your specific length needed, 28 and 31 Spline Long axle is 33" from face of axle flange to the tip of the splined end with 9-1/4" of spline, 35 Spline Long axle is 31.75" from face of axle flange to the tip of the splined end with 8" of spline., 28,31 and 35 Spline Short axle is 29.5" from face of axle flange to tip of the splines with the 28 and 31 spline having 10 1/8" of spline length and the 35 spline having 8" of spline length Long 28 Spline 9 Inch Ford Cut-to-Fit Axle with Bearing Sku # 91045127-28-LONG Mfr. Part # 91045127-28-LONG Condition New Brand PEM Racing Sold Each Details Info These steel axle shafts have a natural finish and are sold individually. They are perfect for small shops and will allow you to build your own custom width rear end easily. Axle length is measured from the flange to the end of the splines. Be sure to select your choice length; short or long, and either 28, 31 or 35 spline. Circle track / off road application 5/8" thread wheel studs sold separately and Street application 1/2" thread wheel studs sold separately and 9 Inch Ford28, 31 or 35 spline axleLong or Short28/31 Spline Short axle is 29.5" length from face of axle flange to tip of the splines with 10 1/8" of spline length28/31 Spline Long axle is 33" length from face of axle flange to the tip of the splined end with 9-1/4" of spline35 Spline Short Axle is 29.5" length from face of axle flange to tip of the splines with 8" of spline length35 Spline Long Axle is 31.75" length from face of axle flange to the tip of the splined end with 8" of splineAxle has the new style big bearing ends on itBearing measures 3.150"Bearings already pressed in2-1/2" OffsetDrilled for 5 on 4-1/2", 5 on 4-3/4", and 5 on 5" wheel bolt patterns using 0.685" knurl dia.PA20 set bearingAR375 Torino retainerAxle length is from the flange to the end of the splinesAxles sold each, not as a pairAxles have 3 bolt patterns in them: 5 on 4-1/2", 5 on 4-3/4", and 5 on 5"The hub pilot (center of the axle flange) measures 3.055"The O.D. of the axle flange measures 5.93"Hub Register O.D. is different on the 35 spline with 2.78" For more information on determining the proper axle length and the Ford 9 Inch, be sure to check out our tech articles; and . Installation Tips Long: 28/31 Spline Long axle is 33" length from face of axle flange to the tip of the splined end with 9-1/4" of spline 35 Spline Long Axle is 31.75" length from face of axle flange to the tip of the splined end with 8" of spline Short: 28/31 Spline Short axle is 29.5" length from face of axle flange to tip of the splines with 10 1/8" of spline length 35 Spline Short Axle is 29.5" length from face of axle flange to tip of the splines with 8" of spline length Installation Notes: Disc brake kits may require increasing the i/d of the center hole in the rotor to match the o/d register or hub pilot on the axle flange, or reducing the diameter of the register or hub pilot on the axle to fit properly to the i/d of the rotor. When installing new axles in rearends with posi traction differentials, be sure to install the driver's side axle first to keep the splines properly aligned. Failure to do so may move the two splined gears out of alignment, and it may be difficult to install the driver's side axle properly if the passenger side axle is already installed. If installation of passenger side axle is done first it may require two people when installing the driver's side axle, with both parties rotating reach axle until splines are in line and the driver's side axle fully sides into the housing. When cutting axles to desired lengths, it is recommended that the following procedures are performed: Normal steel cutting machinery (cold saw, band saw, chop saw, etc.) Using a sleeve around the axle such as a small piece of PVC tubing - this allows: The axle to be spun in place while being cut A perimeter cut around the outer diameter assisting in keeping the cut square Avoiding the build-up of too much heat by doing a straight cut (like a knife though a stick of butter) To ensure you get the most out of your new 9 Inch components, it is recommended that you perform a proper break-in process: Use a name brand mineral-based gear oil, preferably 85w140 (Extremely high quality synthetic oils may be used once break-in process has been successfully performed) Place vehicle on jack stands and let the rearend spin while the vehicle idles - run transmission in both forward and reverse periodically throughout the process Continue to run the rearend until the pinion gets hot (place hand on bottom of the differential housing to verify this) Proper break-in allows: The ability to install new axles and hit the track the same day without worry Extended life for rearend components Keeps the quality and life of your gear oil Also available for consideration when a replacement axle bearing retainer for either of the following Ford applications may be required: Big Ford Old Style Axle Housing Bearing Retainer Application # Big Ford New Style Axle Housing Bearing Retainer Application # Specs Material Type Steel Sold in Quantity Each Finish Natural Spline Count 28 Bolt Pattern Multi: 5 on 5" | 4.75" | 4.50" Overall Length 33 Spline Length 9.25 Offset 2.50 Position Rear Wheel Studs Included No Axle Type Single Shaft Notes Wheel studs not included. Sold separately. See suggested sku #s below. Cut to Fit Yes MFG. Part # 91045127-28-LONG Housing End Style Big Ford/New Style (Torino) Stud Diameter 0.68 Reviews Good part workout good for the job that I was doing Rated by Tony on September 24, 2021 Summary: Good part for the job that I was doing Yes, I recommend this product. great Rated by james on June 09, 2021 Summary: great Yes, I recommend this product. I would buy this product again. Rated by Doogie on May 20, 2021 Summary: Only way to go if you have to run a stock rear end. Pros: These axles are the only way to go! Yes, I recommend this product. yes Rated by dan on February 04, 2021 Summary: would have like to have had the option to get the axle with out a bearing had to remove the bear that it came with to install the bearing i needed to run extra cost just to throw away. but other wise all was good Yes, I recommend this product. Perfect t Rated by DAVID DEL PINO on September 16, 2020 Summary: Cut to suit your desired length.....and perfection. Anything else is asking too much Pros: Fit perfect !!!! Yes, I recommend this product. Related Items / Suggested Parts Speedmaster PCE213.1007 Ford 9 Inch 35 Spline Drag Spool Dorman 610-446 1/2-20 x 1.9 Inch Press-In Wheel Studs, .685 Knurl Moroso 46190 Press-In Wheel Studs, 1/2-20 x 3 Inch, .685 Inch Diameter Axle Bearing Retainer, Big Ford New Style Axle Application Tech Support We're here to help before and after your purchase. If you have a question or need assistance with one of our products, please contact us through eBay Messaging and a knowledgeable Speedway Motors team member will be happy to help. About Speedway Motors is America’s Oldest Speed Shop® and has been a trusted source for specialty rodding and racing products and friendly expert advice for more than 72 years. Founded in 1952 by “Speedy” Bill Smith – a racer and street rodder himself – Speedway has grown from a one-man operation to become the world’s largest manufacturer, distributor and retailer of street rod and racing products. Our industry-leading fast delivery is the result of same-day shipping from our state-of-the-art, centrally located 500,000 sq. ft. headquarters. Speedway’s size offers customers unmatched product selection and low pricing, while our excellent technical support and customer service have made us a recognized leader in the rodding and racing industries.

Price: 164.99 USD

Location: Lincoln, Nebraska

End Time: 2024-08-21T11:02:41.000Z

Shipping Cost: 0 USD